The specific process of brine mushroom killing
Dec 05, 2024

Preparatio
1. Equipment and container preparation: Choose suitable killing equipment, commonly stainless steel pots or professional killing machines. Make sure the equipment is clean, oil-free, rust-free, and can be heated evenly. At the same time, prepare clean containers for holding the mushrooms after killing, such as stainless steel basins or plastic baskets. The containers need to be cleaned and disinfected in advance. They can be boiled in boiling water or soaked in food-grade disinfectants and then rinsed with clean water.
2. Water preparation: Prepare enough clean drinking water, generally enough to completely immerse the mushrooms. Pour the water into the killing equipment and heat it to boiling.
Mushroom placement
1. Selection and sorting: Before putting mushrooms for killing, the selected, graded, and cleaned mushrooms need to be checked again to remove those that may be damaged, have obvious pests or diseases, or are underdeveloped during transportation, to ensure that the quality of the mushrooms put in for killing is basically the same.
2. Appropriate amount of placement: Put the sorted mushrooms into boiling water in batches and in appropriate amounts. The amount of mushrooms put in should be moderate to avoid putting too much in at one time, which will cause the mushrooms to pile up in the water, heat unevenly, and affect the killing effect. Generally, according to the size and capacity of the killing equipment, an appropriate amount of mushrooms can be put in each time so that the mushrooms can be distributed more loosely in the water to ensure that each mushroom can fully contact the boiling water.


Killing operation
1. Control time: Start timing immediately after the mushrooms are put into boiling water. The killing time varies according to factors such as the type and size of the mushrooms and the heating efficiency of the equipment. Generally speaking, the killing time of common varieties such as oyster mushrooms and Agaricus bisporus is usually about 3-5 minutes; the killing time of mushrooms with relatively thick textures such as shiitake mushrooms may need to be extended to 5-8 minutes. During the killing process, the state of the mushrooms should be closely observed. When the color of the mushrooms changes from light to dark, and the surface of the cap becomes brighter and elastic, it can be preliminarily judged that the killing is completed, but it is still necessary to strictly follow the prescribed time.
2. Stir evenly: During the killing process, use appropriate tools (such as a long-handled colander or a special stirring rod) to gently stir the mushrooms so that the mushrooms are constantly turned in the boiling water to ensure that each part of each mushroom is evenly heated to avoid local overheating or insufficient killing. The stirring frequency can be performed every 30 seconds to 1 minute, and the action should be gentle to prevent damage to the appearance of the mushrooms.
Judgment of killing completion
1. Appearance characteristics: The color of the cap of the mushrooms after killing will become relatively uniform and shiny, no longer showing the fresh color when growing, but a slightly mature feeling after processing. The stem will also become more compact and elastic.
2. Texture changes: Gently pinch the mushrooms after killing with your hands, and you will feel that their texture is more compact than before killing, with a certain toughness, not easy to crush, but not too hard, and the whole presents a moderate elastic state.

Cooling treatment
1. Quick transfer: Once it is judged that the killing is completed, use a colander or other tools to immediately remove the mushrooms from the boiling water and quickly transfer them to the pre-prepared cold water for cooling. This step should be completed as quickly as possible to prevent the mushrooms from continuing to be heated by residual heat and affecting their quality.
2. Fully cool: After placing the mushrooms in cold water, stir the mushrooms in the cold water continuously so that the mushrooms can quickly dissipate heat and cool to room temperature. Generally, stirring and cooling are required for about 2-3 minutes to ensure that the temperature inside the mushrooms can also be quickly reduced and restored to normal temperature, to better maintain the crisp and tender taste and original quality of the mushrooms and prepare for subsequent pickling and other processes.
Through the above-detailed process flow, the salted mushrooms can be more effectively treated to ensure that they can maintain good quality and appearance during subsequent processing.

